中文版
sitemap
Time : 2018-04-12
May 10th to 13th, 2018, the highly globalized commercial atmosphere will be once again filled with the Exhibition Centre Guangzhou. The four-day exhibition of Prolight + Sound Guangzhou show will bring together the most representative manufacturers and top level products to present the latest trends of the industry.
Time : 2018-11-30
Time : 2018-11-21
Time : 2018-10-31
INFORMATION CENTER
PRODUCT CATEGORY
What are the safety fire prevention measures for stage lighting?
2018-10-26

A series of fires indicate that stage lighting fire protection design is very important. Then, how can the stage lighting fire protection be designed to pass the fire safety inspection and be deemed qualified?


Reasonable selection of lamp types

------------------------------------------------------------------------------------------------------------------------------------------------------------------

In explosion-prone mixtures, or where it is prone to produce explosive media during production, an integral explosion-proof device should be used. For corrosive gases and particularly humid places, sealed or moisture-proof luminaires shall be used, and the components shall be treated with anti-corrosion treatment. Floodlights can be used in hot and dusty places (such as steelmaking, iron making, steel rolling, etc.). Outdoor lighting can be enclosed lamps or open lamps with fire lamp holders.



Lighting and decorative lighting should be properly installed

-------------------------------------------------------------------------------------------------------------------------------------------

(1) The distance between the lamps and the combustibles shall not be less than 50 cm (the tungsten halogen lamps shall be greater than 50 cm), and the height of the ground shall not be less than 2 m. When the height is lower than this, protective equipment shall be installed. It is not advisable to stack combustible items under the bulb.

 

(2) The protective cover of the luminaire must be intact. It is strictly forbidden to cover the luminaire with paper, cloth or other combustible materials.

 

(3) The power of all concealed and surface mounted lamps on the flammable ceiling should not be too large, and should be dominated by incandescent or fluorescent lamps. The surrounding lamps and their heating accessories should have good heat dissipation conditions. The conductors of the stage concealed lanterns, dance floor lamps and flammable ceiling lamps shall be laid with steel pipes or flame-retardant hard plastic casings; the wires near the tungsten halogen lamps shall be made of heat-resistant insulating sheaths; There should be a rubber ring protection through the keel.

 

(4) Selecting low-quality ballasts with reliable quality, it is not allowed to directly fix the ballasts with high temperature rise on objects such as combustible large-flower plates, and the capacitance and capacity must be consistent with the lamps.

 

(5) Class 0, Class 10 explosion hazardous places (0 level area refers to explosive gas, level 10 area refers to explosive dust), when opening type lamps are used to make wall-mounted alcove, the access door should be outside the wall. Open and ensure good ventilation; the side that is illuminated indoors should be sealed with double glazing. The horizontal distance from the door and the window frame is not less than 3 meters, and the horizontal distance from the air outlet is not less than 5 meters.



Reasonable control of electrical lighting

----------------------------------------------------------------------------------------------------------------------------------

The lighting currents should each have their own branch circuit and should not be connected after the main power switch. Short circuit protection facilities shall be provided for each branch circuit. In order to avoid accidents caused by overload and heat, some important places and inflammable and explosive materials must also be equipped with overload protection devices. Non-explosion-proof lighting distribution boxes and control switches are strictly forbidden to be used in Class 0 and Class 10 explosion hazardous areas. Minimize the joint after the switchboard, and the disk surface should be well grounded.



The stricter the lighting voltage level and load

------------------------------------------------------------------------------------------------------------------------------------------------------------------

The lighting voltage is generally 220 volts, the supply voltage of portable lighting fixtures should not exceed 36 volts, and in wet areas should not exceed 12 volts, and autotransformers are prohibited. Power outlets below 36 volts and above 220 volts should have significant differences and markings.

 

The number of lamps in a branch circuit should not exceed 20, the civil lighting current should be less than 15 amps, and the industrial use should be less than 20 amps. The wire size is determined by the amount of load (each socket is measured with a load of 2 to 3 amps). The three-phase four-wire lighting circuit should also be balanced with three-phase load.

 

Accident lighting fixtures should be located in places prone to accidents, main entrances and exits of buildings, important workplaces, etc., and marked with obvious color markings for timely and convenient activation. Accident lighting fixtures cannot be of a slow start type (such as ballast starters, etc.). Accident lighting fixtures should be powered by an independent emergency battery to ensure that the normal power system is properly opened when unaffected.




Guangzhou FEIPENG Stage Lighting Co.,Ltd
  • Tel: +86 29046476
  • Skype: hc_rexwong
  • zip: 510430
  • E-mail: info@oppray-light.com
  • Website: www.oppray-light.com

Office Address : Room 603,Qiangsheng Business Building A, No.168 Jiangxia North Road,Baiyun district.Guangzhou

Factory Address : NO. 18 Jiangshi Road Hebu Villiage Jianggao Town Baiyun District Guangzhou

Friend Links